Before you begin Read this website's Legal Guidelines and make sure you understand the risks of this repair. Place your Microsoft Zune 2 on a clean flat and soft surface, such as a rubber mat or a piece of soft cloth and get the required opening tools
		Step 1discount drugs canada Best price for gleevec Prescription dose of benadryl p o Macrobid forum K-y intense arousal gel coupon Generic cymbalta 60 m g israel Hydrochlorothiazide constipation Grot soma graffiti Azor oral Testimonies of viagra use South african suppliers of cialis Buy cialis generic Clarinex mood Decreasing efficacy of detrol
		Step 2 The gap between the bottom of the screw cover and the front plate is the best place to insert the safe open tool.
		Step 3 If you twist the safe open tool the screw cover will pop off exposing two Torx T4 screws.
		Step 4 Use your Torx T4 screwdriver to remove them.
		Step 5 Pry between the front and backplate next to the aperture of the screw cover.
		Step 6 Slide the tool toward the edge, thereby widening the gap between backplate and frontplate on the right side of your Zune II. You can try to slide the tool all the way around the edge. If that fails, reinsert the tool of the right side.
		Step 7
		Step 8 Slide the tool all along the side to the bottom of the Zune.
		Step 9   Repeat the last steps and twist the safe open tool. You will need to apply some force here and be patient until the backplate will come loose.
		Step 10 Sometimes you may not succeed with the plastic tool alone. You can use the flathead screwdrive which will give you more torque, but is also more likely to cause cosmetic damage.
		Step 11 Once the back was release from all clips you can lift it up and set it aside.
		Step 12 You have successfully opened your Zune 2.

		Warning - This repair requires soldering skills. Step 13 As you can see this battery is defective and needs to be replaced. Begin by removing the shielding foil taped over the top of the hard drive.
		Step 14 Pry up the Zune hard drive using the opening tool.
		Step 15 Lift up the hard drive and pay attention to the ribbon cable at the bottom of the hard drive. It is extremely sensitive. Make sure the cable does not get punctured or dented.
		Step 16 Peel off the shielding foil over the audio jack ribbon cable and battery cable. Don't tear it or damage it, it needs to be re-applied upon reassembly. In General: be very careful with the shielding foil on all components, if it is not reapplied correctly it can keep the Zune from powering up properly after reassembly.
		Step 18   Use the opening tool as a lever to pry the Zune Battery loose from the double sided tape on it's bottom.
		Step 19 In the image you see how the battery is soldered to the zune logic board. Use a soldering iron to disconnect the defective battery.
		Step 20 Connect the new battery to the solder pads using the same color coding as the original battery.  For reassembly follow the steps in reverse order. Remember to reapply all aluminum shielding foil.

		Prepare Tools required: Small Phillips Screw Driver Small Flathead Safe Open Tool Set aside all neccesary tools and place your Zune 1 on a soft material to protect it from scratches.
		Behold Firmly imprint this image on your mind, the Zune should look more or less like this again after reassembly.
		Step 1 Begin by removing the screw cover at the dock connector using the flathead screwdriver as shown in image.
		Step 2 Remove the two screws under the cover.
		Step 3 Insert a small thin tool between the chrome ring and front panel glass directly above one of the screw holes. You will need to exert a small amount of pressure to seperate the display from the back panel.
		Step 4 Pry up the Backplate by using the safe open tool.
		Step 5 Slide the safe open tool around the sides.
		Step 6 Slide the safe open tool around the top, thereby releasing the backplate entirely.
		Step 7 Lift up the backplate.
		Step 8 Remove the screws circled in red.
		Step 9 Flip over to the bottom of the device and remove the screws on the bottom of the hard drive casing.
		Step 10 Release the latch of the battery connector.
		Step 11 Remove the four screws at the top and bottom of the hard drive enclosure.
		Step 12 Carefully lift the hard drive enclosure off the logic board.
		Step 14 Turn around the hard drive enclosure, open the latch of the hard drive flex connector and pull out the ribbon cable.
		Step 15 Remove the screws holding the logic board to the front plate.
		Step 16 Genly lift up the logic board and release it from the front plate.
		Step 17 Release the ribbon cable of the button pad and place the logic board aside.
		Step 18 - Back to the Front Half Remove all screws of the button pad cover.
		Step 18 Lift the button pad cover off the button pad. You have fully disassembled your Zune 1, to re-assemble it follow the steps in reverse order.